| Sampling Rate (Max.) |
1 GSa/s (One channel), 500 MSa/s(Two channels), 250 MSa/s(Four channels) |
| Memory Depth (Max.) |
14 Mpts |
| Peak Detect |
2 ns |
| Average |
Averages: 4,16, 32, 64, 128, 256, 512, 1024 |
| Eres |
Enhance bits: 0.5, 1, 1.5, 2, 2.5, 3 |
Waveform
interpolation |
Sin(x)/x, Linear |
| Input |
|
| Channels |
4 |
| Coupling |
DC, AC, GND |
| Impedance |
DC: (1 MΩ±2%) || (11 pF ±2 pF) |
| Max. Input Voltage |
1 MΩ: ≤400 Vpk (DC + Peak AC <=10 kHz) |
| CH to CH Isolation |
DC-Max BW :>40 dB |
| Probe Attenuation |
1E-6X ~ 1E6X |
| Vertical System |
|
| Bandwidth (-3dB) |
100 MHz |
| Vertical Resolution |
8-bit |
Vertical Scale (Probe
1X) |
1 mV/div – 10 V/div (1-2-5 sequence) |
Offset Range (Probe
1X) |
1 mV- 200 mV: ± 2 V
206 mV- 10 V: ± 100 V |
| Bandwidth limit |
20 MHz ± 40% |
| Bandwidth Flatness |
DC- 10% (BW): ± 1 dB
10% – 50% (BW): ± 2 dB
50% – 100% (BW): + 2 dB/-3 dB |
Low frequency
response
(AC coupling -3 dB) |
≤2 Hz (at input BNC) |
| Noise |
ST-DEV ≤ 0.2 division (<2 mV/div)
ST-DEV ≤ 0.1 division (≥ 2 mV/div) |
SFDR including
harmonics |
≥ 35 dB |
| DC Gain Accuracy |
≤ ± 3.0%: 5 mV/div-10 V/div
≤ ± 4.0% : ≤ 2 mV/div |
| Offset Accuracy |
± (1%* Offset+1.5%*8*div+2 mV): ≥2 mV/div
± (1%* Offset+1.5%*8*div+500 uV): 1 mv/div |
| Rise time |
Typical 3.5 ns |
Overshoot (500 ps
Pulse) |
< 10% |
| Horizontal System |
|
| Timebase Scale |
2 ns/div-100 s/div |
| Channel Skew |
<100 ps |
Waveform Capture
Rate |
Up to 100,000 wfm/s (normal mode), 400,000 wfm/s (sequence mode) |
| Intensity grading |
256 Levels |
| Display Format |
Y -T, X -Y, Roll |
| Timebase Accuracy |
±25 ppm |
| Roll Mode |
50 ms/div-100 s/div (1-2-5 sequence) |
| Trigger System |
|
| Mode |
Auto, Normal, Single |
| Level |
Internal: ±4.5 div from the center of the screen |
| Hold off range |
80 ns- 1.5 s |
| Coupling |
AC
DC
LFRJ
HFRJ
Noise RJ |
Coupling Frequency
Response |
DC: Passes all components of the signal
AC: Blocks DC components and attenuates signals below 8Hz
LFRJ: Blocks the DC component and attenuates the low-frequency
components below 2 MHz
HFRJ: Attenuates the high-frequency components above 1.2 MHz |
| Accuracy (typical) |
Internal: ±0.2 div |
| Sensitivity |
DC – Max BW 0.6 div |
| Jitter |
<100 ps |
| Displacement |
Pre-Trigger: 0 – 100% Memory
Delay Trigger: 0 to 10,000 div |
| Edge Trigger |
|
| Slope |
Rising, Falling, Rising & Falling |
| Source |
All channels/AC Line |
| Slope Trigger |
|
| Slope |
Rising, Falling |
| Limit Range |
＜, ＞, ＜＞, ＞＜ |
| Source |
All channels |
| Time Range |
2ns- 4.2s |
| Resolution |
1ns |
| Pulse Width Trigger |
|
| Polarity |
+wid , -wid |
| Limit Range |
＜, ＞, ＜＞, ＞＜ |
| Source |
All channels |
| Pulse Range |
2 ns – 4.2s |
| Resolution |
1 ns |
| Video Trigger |
|
| Signal Standard |
NTSC，PAL，720p/50，720p/60，1080p/50，1080p/60，1080i/50，1080i/60，Custom |
| Source |
All channels |
| Sync |
Any, Select |
| Trigger condition |
Line, Field |
| Window Trigger |
|
| Window Type |
Absolute, Relative |
| Source |
All channels |
| Interval Trigger |
|
| Slope |
Rising, Falling |
| Limit Range |
＜, ＞, ＜＞, ＞＜ |
| Source |
All channels |
| Time Range |
2 ns – 4.2 s |
| Resolution |
1 ns |
| Dropout Trigger |
|
| Timeout Type |
Edge, State |
| Source |
All channels |
| Slope |
Rising, Falling |
| Time Range |
2 ns – 4.2 s |
| Resolution |
1ns |
| Runt Trigger |
|
| Polarity |
+wid , -wid |
| Limit Range |
＜, ＞, ＜＞, ＞＜ |
| Source |
All channels |
| Time Range |
2 ns – 4.2 s |
| Resolution |
1 ns |
| Pattern Trigger |
|
| Pattern Setting |
Invalid, Low, High |
| Logic |
AND, OR, NAND, NOR |
| Source |
All channels |
| Limit Range |
＜, ＞, ＜＞, ＞＜ |
| Time Range |
2 ns – 4.2 s |
| Resolution |
1 ns |
| I2C Trigger |
|
| Condition |
Start, Stop, Restart, No Ack, EEPROM, 7-bits Address & Data, 10-bits Address & Data, Data Length |
| Source(SDA/SCL) |
All channels |
| Data format |
Hex |
| Limit Range |
EEPROM: =, >, < |
| Data Length |
EEPROM: 1byte
Addr & Data: 1-2byte
Data Length: 1-12byte |
| R/W bit |
Addr & Data: Read, Write, Do not care |
| SPI Trigger |
|
| Condition |
Data |
| Source(CS/CL/Data) |
All channels |
| Data format |
Binary |
| Data Length |
4-96-bit |
| Bit Value |
0, 1, X |
| Bit Order |
LSB, MSB |
| UART Trigger |
|
| Condition |
Start, Stop, Data, Parity Error |
| Source(RX/TX) |
All channels |
| Data format |
Hex |
| Limit Range |
=, >, < |
| Data Length |
1 byte |
| Data Width |
5, 6, 7, 8-bits |
| Parity Check |
None, Odd, Even, Space, Mark |
| Stop Bit |
1, 1.5, 2-bits |
| Idle Level |
High, Low |
| Baud Rate(Selectable) |
600/1200/2400/4800/960019200/38400/57600/115200 bit/s |
| Baud Rate (Custom) |
300-5000000 bit/s |
| CAN Trigger |
|
| Condition |
Start, Remote, ID, ID + Data, Error |
| Source |
All channels |
| ID |
STD (11-bits), EXT (29-bit) |
| Data Format |
Hex |
| Data Length |
1 -2 byte |
| Baud Rate |
5k/10k/20k/50k/100k/125k/250k/500k/800k/1 Mbit/s |
| LIN Trigger |
|
| Condition |
Break, Frame ID, ID+Data, Error |
| Source |
All channels |
| ID |
1byte |
| Data Format |
Hex |
| Data Length |
1-2byte |
Baud Rate
(Selectable) |
600/1200/2400/4800/9600/19200 bit/s |
| Baud Rate (Custom) |
300 bit/s -20 kbit/s |
| I/O |
|
| Standard |
USB Host, USB Device, LAN, Pass/Fail, Trigger Out |
| Pass/Fail |
3.3V TTL Output |
| General Specifications |
|
| Input Voltage |
100 ～ 240 Vrms 50/60Hz
100 ～ 120 Vrms 400Hz |
| Power |
50 W Max |
| Temperature |
Operating: 0℃ – +40℃
Non-operating: -20℃ – + 60℃ |
| Humidity |
Operating: 85% RH, 40 ℃, 24 hours
Non-operating: 85% RH, 65 ℃, 24 hours |
| Height |
Operating: ≤ 3000 m
Non-operating: ≤ 15,000 m |
| Display Type |
7–inch TFT LCD |
| Display Resolution |
800×480 pixels |
| Display Colour |
24-bit |
| Contrast(Typical) |
500:1 |
| Backlight |
300 nits |
| Range |
8 x 14 divisions |
| Dimensions |
Length: 312 mm
Width: 132.6 mm
Height: 151 mm |
| Weight |
N.W: 2.6 kg; G.W: 3.8 kg |
Siglent SDS1000X-U Datasheet
Reviews
There are no reviews yet.